Print time is too inaccurate
by ftdesigns » Wed Dec 11, 2019 11:54 am » in Troubleshooting and Bug Reports

Program Splitting Large Model
by FairfieldFoundation » Wed Dec 11, 2019 10:47 am » in Troubleshooting and Bug Reports

Vase Mode Leaving Voids in ALL Models
by adikted2astro » Wed Dec 11, 2019 1:41 am » in Troubleshooting and Bug Reports

Anycubic Kossel Extrusion Problem
by xeraj85 » Fri Dec 06, 2019 12:55 pm » in Troubleshooting and Bug Reports

Better support for the Flashforge Finder
by Archer3D » Fri Dec 06, 2019 11:04 am » in Feature Requests

F/W Retraction Min Travel not working
by xboxhacker » Thu Dec 05, 2019 9:41 am » in Troubleshooting and Bug Reports

Can't print on Anycubic Predator directly
by alexsaraev » Sun Dec 01, 2019 12:34 pm » in Troubleshooting and Bug Reports

Ender 5 with TH3D firmware and Silent Board
by demetri90 » Sun Dec 01, 2019 10:23 am » in Troubleshooting and Bug Reports

3dlabprint F86 F8
by St0mp » Sat Nov 30, 2019 6:49 pm » in Troubleshooting and Bug Reports

New revision of a model produces banding
by yeahtuna » Sat Nov 30, 2019 3:11 am » in Troubleshooting and Bug Reports

Switched Extruders on BCN3D Sigma
by mcocroft » Fri Nov 29, 2019 6:31 pm » in Troubleshooting and Bug Reports

Lines in surface
by bdaehn » Wed Nov 27, 2019 7:17 am » in Troubleshooting and Bug Reports

speed first bottom and last top layer
by Zaitek » Tue Nov 26, 2019 4:55 am » in Troubleshooting and Bug Reports

can't connect USB / Wifi to 3D printer
by ice0tea » Sat Nov 23, 2019 3:55 am » in Troubleshooting and Bug Reports

Supports are bad.
by danielmccutcheon » Thu Nov 21, 2019 10:42 pm » in Troubleshooting and Bug Reports

Switching printers problem
by billyd » Wed Nov 20, 2019 8:27 pm » in Troubleshooting and Bug Reports

Pause to Embed magnet or nut
by SouthernGoose » Sun Nov 17, 2019 10:20 pm » in Feature Requests

FlashForge Guider IIs
by Euroeng » Wed Nov 13, 2019 1:14 pm » in Troubleshooting and Bug Reports

Printer not accepting commands?
by lolixuli » Wed Nov 13, 2019 4:47 am » in Troubleshooting and Bug Reports

Discontinuity in critical perimeter
by Rovert » Wed Nov 13, 2019 4:13 am » in Troubleshooting and Bug Reports

Bed area Raise Pro 2 Plus
by nickhulinsky » Mon Nov 11, 2019 3:06 pm » in Troubleshooting and Bug Reports

CTC Bizer firmware troubleshooting
by robertodippolito » Mon Nov 11, 2019 5:13 am » in Troubleshooting and Bug Reports

multiple process printing - start/stop printing at height in mm vs layer
by airscapes » Fri Nov 08, 2019 11:44 am » in Feature Requests

Lithophane print quality
by yaksha42 » Thu Nov 07, 2019 11:07 pm » in Troubleshooting and Bug Reports

Move Nozzle to prime tower before switching
by tphan » Thu Nov 07, 2019 3:24 pm » in Troubleshooting and Bug Reports