Search found 80 matches

Go to advanced search

by habloIngles
Sat Jan 24, 2015 3:52 pm
Forum: General Discussion and Tips
Topic: GCODE to prime extrude
Replies: 2
Views: 7540

Re: GCODE to prime extrude

Also, if you're getting burnt/brownish looking gunk, this usually occurs when the nozzle has plastic from previous prints stuck to it. It's good to clean your nozzle every once in a while before you start a print so you don't get any gunk on your prints
by habloIngles
Sat Jan 24, 2015 3:49 pm
Forum: General Discussion and Tips
Topic: Printings freezes at 90%
Replies: 1
Views: 556

Re: Printings freezes at 90%

Check the communication log and see what it says when the print stops, your printer may be returning a clue as to why this is happening. If it doesn't happen in the same exact spot everytime, I would definitely say it's something with the printer and not the gcode itself
by habloIngles
Fri Jan 23, 2015 10:37 am
Forum: General Discussion and Tips
Topic: Rostock Max V2 fans not turning on
Replies: 3
Views: 1013

Re: Rostock Max V2 fans not turning on

Try opening up the machine control panel (with the Rostock on and connected) send in an M106 S255 to make sure the fan turns on. This is to verify that the M106 is the right G-Code command to control the fan. If that checks out, then I would slice a model, export the G-Code and then open the G-Code ...
by habloIngles
Thu Jan 15, 2015 9:23 am
Forum: Troubleshooting and Bug Reports
Topic: Simplify3D crashed (Linux)
Replies: 4
Views: 1550

Re: Simplify3D crashed (Linux)

What specific connection error are you getting? Also have you tried this?

http://www.forum.simplify3d.com/viewtop ... 1544#p5852
by habloIngles
Thu Jan 15, 2015 8:36 am
Forum: General Discussion and Tips
Topic: Tip of the Day 3- Steps Per MM, tolerances and more!
Replies: 6
Views: 17372

Re: Tip of the Day 3- Steps Per MM, tolerances and more!

look forward to reading these everyday good job mate. Gonna have to check back regularly so I don't miss one before it gets lost into the forray
by habloIngles
Tue Jan 13, 2015 6:09 pm
Forum: Troubleshooting and Bug Reports
Topic: Why it's different ?
Replies: 2
Views: 1222

Re: Why it's different ?

Makerbot style printers (flashforge) that run sailfish firmware use a binary communication protocol and not ascii based gcode like RepRap style firmware like Marlin, Repetier, etc. (your leapfrog). That's why you see different looking communication text, and this is why a lot of people like s3d. Ins...
by habloIngles
Tue Jan 13, 2015 6:05 pm
Forum: Feature Requests
Topic: [ADDED] LinuxCNC gcode output request
Replies: 7
Views: 3861

Re: LinuxCNC gcode output request

I emailed support as Im using a modified marlin firmware provided by someone else and it uses A instead of E as well. Go to the scripts tab and in hte post processing section, use this:
{REPLACE "E" "A"}
by habloIngles
Tue Jan 13, 2015 6:02 pm
Forum: General Discussion and Tips
Topic: Tip of the Day 1- FlashForge Dreamer Lights
Replies: 2
Views: 1907

Re: Keyboard Warrior Tip of the Day1- FlashForge Dreamer Lig

that seems pretty cool! I would definitely use this as a visual indicator of different print stages (i.e. heating up, printing, done), wish i had a dreamer :(
by habloIngles
Mon Jan 12, 2015 9:04 pm
Forum: Feature Requests
Topic: Mac Version Tweaks
Replies: 14
Views: 4529

Re: Mac Version Tweaks

Some of these sound very handy
by habloIngles
Mon Jan 12, 2015 9:04 pm
Forum: General Discussion and Tips
Topic: UM2 - occasional violent build bed vibrate on print initiate
Replies: 1
Views: 673

Re: UM2 - occasional violent build bed vibrate on print init

If the problem is intermittent and sometimes a gcode file will print and sometimes the same gcode file will cause this issue, I would suspect it's a firmware issue.

Go to advanced search