Search found 848 matches

Go to advanced search

by horst.w
Wed Nov 27, 2019 4:09 am
Forum: Troubleshooting and Bug Reports
Topic: Thin walls not Infilling and Top Layers not sealing
Replies: 8
Views: 820

Re: Thin walls not Infilling and Top Layers not sealing

I have read that the S3D Terms of Service prohibit publicly posting Factory Files, and that specific queries of S3D on this issue were not definitively resolved. Did I misunderstand what I read, or was it just inaccurate? Can you shed any light on this matter? The restriction is only available for ...
by horst.w
Tue Nov 26, 2019 2:42 pm
Forum: Troubleshooting and Bug Reports
Topic: Thin walls not Infilling and Top Layers not sealing
Replies: 8
Views: 820

Re: Thin walls not Infilling and Top Layers not sealing

No answer is also an answer! I have found this here: https://forum.simplify3d.com/viewtopic.php?f=9&t=14061&p=53135#p53135 You are well knowing what a factory file is, but you avoid to show it. If you are using a cracked version such like "Licensed for God", than it wasn't a good idea to ask here fo...
by horst.w
Tue Nov 26, 2019 3:05 am
Forum: Troubleshooting and Bug Reports
Topic: Thin walls not Infilling and Top Layers not sealing
Replies: 8
Views: 820

Re: Thin walls not Infilling and Top Layers not sealing

A FFF-Profil doesn't replace a FACTORY-File! A factory contains also the STL of the model and this is needed to find out the reason. Nevertheless try out to set INFILL >>> Minimum Infill Length down to zero (now 1 mm). You are using version 4.01. If I remember right, this version was a little bit fa...
by horst.w
Thu Nov 21, 2019 6:15 pm
Forum: Troubleshooting and Bug Reports
Topic: Strange printing speed with Simplify3D
Replies: 12
Views: 1255

Re: Strange printing speed with Simplify3D

Generally a positive restart distance doesn't avoid oozing, it produce oozing. Compensation may be possible by using Coast and wipe and a high rate of Multiplier. But this parameters must be balanced very very well, based on best standard settings. Don't put the cart before the horse. Fact is that y...
by horst.w
Thu Nov 21, 2019 5:16 am
Forum: Troubleshooting and Bug Reports
Topic: Strange printing speed with Simplify3D
Replies: 12
Views: 1255

Re: Strange printing speed with Simplify3D

I think simplify calculate a wrong amount of material. As a result of this are the artifacts on the outer shell. some print parameters could be wrong. I accidentally delete some of my profiles and had the create them new (but they aren't tested yet). Surely NO, the artifacts are caused by your sett...
by horst.w
Thu Nov 21, 2019 3:14 am
Forum: Troubleshooting and Bug Reports
Topic: Strange printing speed with Simplify3D
Replies: 12
Views: 1255

Re: Strange printing speed with Simplify3D

2. point:

the bad print quality is mainly caused by your faulty settings.

Multiplier 1,10 ??? what the exact messure of the filaments diameter; 1.75 may be only the nominal value
Restart Distance positive ??? should be negative
Coasting ???
Wiping ???
Print Temperature ???


H.
by horst.w
Thu Nov 21, 2019 3:02 am
Forum: Troubleshooting and Bug Reports
Topic: Strange printing speed with Simplify3D
Replies: 12
Views: 1255

Re: Strange printing speed with Simplify3D

Hi Buckker, I'm sorry, but I can't see what the problem is with your code. The speed, is it to fast or is it to slow??? The print preview looks ok for me, all speeds are in a range, resulting by your settings (Preview > Moving Speeds) If the F-value is the point, please note that GCode transforms th...
by horst.w
Mon Nov 04, 2019 3:27 am
Forum: Troubleshooting and Bug Reports
Topic: How toStrengthen Tall Thin Supports
Replies: 17
Views: 6629

Re: How toStrengthen Tall Thin Supports

Because I have a similar problem, I have played with some solutions. Instead using a complicate support tree it suffers to use a simple shim, an adjusted form or similar . Positioned under the print edge in certain distance, S3D build support from the print table up to the shim and than from the shi...
by horst.w
Sun Nov 03, 2019 7:26 am
Forum: Troubleshooting and Bug Reports
Topic: How toStrengthen Tall Thin Supports
Replies: 17
Views: 6629

Re: How toStrengthen Tall Thin Supports

.... an additional STL you can add anytime ...

H.
Support_test3.jpg
by horst.w
Sun Nov 03, 2019 3:16 am
Forum: Troubleshooting and Bug Reports
Topic: How toStrengthen Tall Thin Supports
Replies: 17
Views: 6629

Re: How toStrengthen Tall Thin Supports

Hi Wirlybird, I would try to add a cylinder or similar under as an additional part, just up to the last 5 mm . Use a separate process for it, support must be set to "Normal". With an elefantfoot on the additional part and sufficient support distance to objects of the main model you can avoid support...

Go to advanced search