Search found 1238 matches

Go to advanced search

by wirlybird
Wed Sep 11, 2019 5:47 pm
Forum: Troubleshooting and Bug Reports
Topic: Stringing
Replies: 10
Views: 2640

Re: Stringing

You probably could. I changed the script for mine to set a static IP for it. I think if you know the IP, which you can get from the control panel, then plug into it you may be able to enter it into your browser and get into the interface. Worst case is you might need a cross over cable to go direct,...
by wirlybird
Wed Sep 11, 2019 5:43 pm
Forum: General Discussion and Tips
Topic: Process, Profiles, Printers, Tuning, how to?
Replies: 13
Views: 4476

Re: Process, Profiles, Printers, Tuning, how to?

Understand.

I have one printer that I run a 0.4, 0.6 or 0.8 in both brass and hardened.
So I have a profile for each nozzle and material.

So I have a F410 PLA o.4 brass and a F410 PLA 0.4 Hardened.

Anyway I think do it however works for you. Sounds like you are developing a system that works.
by wirlybird
Wed Sep 11, 2019 3:23 pm
Forum: Troubleshooting and Bug Reports
Topic: Stringing
Replies: 10
Views: 2640

Re: Stringing

That's consistent with my results printing PLA temperature towers, and I found it odd since most online communities would tell you stringing happens less at the lower end of the transition temps. My conclusion on this is it is their hardened nozzle. These are a whole different game when it comes to...
by wirlybird
Wed Sep 11, 2019 3:15 pm
Forum: General Discussion and Tips
Topic: Process, Profiles, Printers, Tuning, how to?
Replies: 13
Views: 4476

Re: Process, Profiles, Printers, Tuning, how to?

That's why I make my profile name mostly to relate to a particular machine and state such as MK3 PLA 0.4 Brass where that machine uses brass or hardened nozzle setups. Otherwise I don't care to list layer height or any other settings since I just change them as I need but this particular profile is ...
by wirlybird
Wed Sep 11, 2019 2:42 pm
Forum: General Discussion and Tips
Topic: Process, Profiles, Printers, Tuning, how to?
Replies: 13
Views: 4476

Re: Process, Profiles, Printers, Tuning, how to?

I think you are doing basically what I do. I run 11 printers at the moment and some are only ABS or FLEX etc. What I do is take the "default" profile for a particular printer and material such as Printer A - PLA and I save it as a new one something like My Printer A - PLA 0.4 Brass or MK3 - PLA. So ...
by wirlybird
Wed Sep 11, 2019 1:33 pm
Forum: Troubleshooting and Bug Reports
Topic: Connecting Makerbot Replicator 2X to Machine CP
Replies: 8
Views: 1278

Re: Connecting Makerbot Replicator 2X to Machine CP

Your printer is using a variant of Sailfish firmware so sending gcodes directly doesn't work.
by wirlybird
Wed Sep 11, 2019 7:13 am
Forum: Troubleshooting and Bug Reports
Topic: single outline corkscrew printing mode does not work
Replies: 15
Views: 1633

Re: single outline corkscrew printing mode does not work

I'm not an idiot. You are sure? How do you assume my model is not printable ? It will be, but not as a hollow body with a definide wall width. Your model has 2 walls, an outer and an inner one. How you want to print it with onle one perimeter? Sir, you havn't understood anything! Go back to Cura, t...
by wirlybird
Mon Sep 09, 2019 12:06 pm
Forum: Troubleshooting and Bug Reports
Topic: Can't get this stl to print as is
Replies: 4
Views: 404

Re: Can't get this stl to print as is

My guess is that those areas (the walls) are too thin to print for your current configuration such as nozzle size or extrusion width.
by wirlybird
Mon Sep 09, 2019 6:50 am
Forum: Troubleshooting and Bug Reports
Topic: Stringing
Replies: 10
Views: 2640

Re: Stringing

I'm having similar issues on a Fusion 3 F410 but for a start, I'd reccomend you increase your retraction distances since its a Bowden, it could want to retract more than 5 mm. Also try increasing your temperatures. Try using https://www.thingiverse.com/thing:2729076 and S3D's variable settings wiza...
by wirlybird
Fri Sep 06, 2019 6:15 am
Forum: Troubleshooting and Bug Reports
Topic: Cross Section View in V4.1.2 Prevents Manual Support Removal
Replies: 0
Views: 792

Cross Section View in V4.1.2 Prevents Manual Support Removal

This is becoming a real problem. You cannot remove supports if you have cross section view open.
How does this big of a problem even make it into a released version of the software?

Go to advanced search