Search found 94 matches

Go to advanced search

by Ayres3D
Fri Oct 19, 2018 4:21 pm
Forum: General Discussion and Tips
Topic: Do I need to reload STL files after changes
Replies: 6
Views: 1042

Re: Do I need to reload STL files after changes

You will need to replace the STL as the original is held in the factory file (AFAIAA)
by Ayres3D
Tue Oct 16, 2018 12:15 pm
Forum: Troubleshooting and Bug Reports
Topic: Help with FlashForge Creator Pro
Replies: 2
Views: 451

Re: Help with FlashForge Creator Pro

That is really odd. It sounds as if the installation on the new machine is simply not working, doesn't it? Have you tried running the Configuration Assistant again? Perhaps even go as far as removing and re-installing S3D completely on the new machine if that doesn't help?
by Ayres3D
Thu Oct 04, 2018 7:30 am
Forum: Troubleshooting and Bug Reports
Topic: Alfawise U20 printer displays "Print finished" although it never started to print !
Replies: 8
Views: 2076

Re: Alfawise U20 printer displays "Print finished" although it never started to print !

I assume that the print preview shows a valid print, does it? Many a time I have forgotten to clear the "Start print at .." height meaning that there was nothing to print.
by Ayres3D
Wed Oct 03, 2018 10:21 am
Forum: Feature Requests
Topic: Simple UI selection of wipe position
Replies: 6
Views: 792

Re: Simple UI selection of wipe position

OK, thank you. Perhaps I'll try it that way then. It did seem like a bit of a niche requirement when I suggested it ;)

Thanks for you help
by Ayres3D
Thu Sep 27, 2018 8:06 am
Forum: Feature Requests
Topic: Simple UI selection of wipe position
Replies: 6
Views: 792

Re: Simple UI selection of wipe position

it doesn't have a specified area as such but what I do at present is apply a layer of blue tape at the default S3D location to make the wipe there more positive. In practice this is the front right corner of the bed, so I have a triangle of one (or two) layers of tape across that corner. This seems ...
by Ayres3D
Thu Sep 20, 2018 10:52 am
Forum: Troubleshooting and Bug Reports
Topic: [SOLVED]Grid missing??
Replies: 2
Views: 414

Re: Grid missing??

Have a look here

viewtopic.php?t=3130
by Ayres3D
Thu Sep 20, 2018 10:50 am
Forum: General Discussion and Tips
Topic: How do you align parts in the dual extruder wizard
Replies: 1
Views: 392

Re: How do you align parts in the dual extruder wizard

If the origins aren't set properly then the slicer isn't going to know where they should align, surely? If you're lucky and they have a common face then you could try aligning but setting that face on the bed on each, but other than that you're a little stuck for it to be done automatically, I imagi...
by Ayres3D
Thu Sep 20, 2018 8:50 am
Forum: Feature Requests
Topic: Simple UI selection of wipe position
Replies: 6
Views: 792

Re: Simple UI selection of wipe position

Yes, I can see that that could help, but ideally a separate setting would be better still as it would divorce the one function from the other. That is, I may have very specific requirements of a skirt or brim and adding the possible variables from a wipe could compromise that. Also, the normal wipe ...
by Ayres3D
Thu Sep 20, 2018 6:31 am
Forum: Feature Requests
Topic: Simple UI selection of wipe position
Replies: 6
Views: 792

Simple UI selection of wipe position

I often work with my printer remotely using remote monitoring. If I'm printing small objects I have the option to perform multiple sequential print runs manually if I want to tweak things without being there to remove the prints. Obviously I need to offset the location of each. Where this falls down...
by Ayres3D
Thu Sep 13, 2018 12:05 pm
Forum: Feature Requests
Topic: Support with outlines for high quality prints
Replies: 4
Views: 753

Re: Support with outlines for high quality prints

If I understand what you're asking then the feature you're looking for is dense support. If you set this to 100% then it will create a 100% layer (or layers, you can select) at the top of the support structure.

Go to advanced search