Search found 18 matches

Go to advanced search

by martin1454
Sat Oct 20, 2018 8:46 am
Forum: General Discussion and Tips
Topic: Does extrusion width affect flow / multiplier?
Replies: 7
Views: 1676

Does extrusion width affect flow / multiplier?

So there is a little bit of gap between the lines of my solid infill - If I change the extrusion width from 0.48mm to 0.45 it looks really good - But does changing the extrusion width change the flow / gcode or only how close the lines are near to each other.
by martin1454
Sat Oct 20, 2018 3:30 am
Forum: Feature Requests
Topic: Retract while coast / un-retract while move
Replies: 5
Views: 1037

Re: Retract while coast / un-retract while move

An older feature but I vote for it -

Also - Retract towards infill instead of along the perimiter would help also!
by martin1454
Sun Oct 14, 2018 2:47 am
Forum: Feature Requests
Topic: Send GCode Directly to OctoPrint
Replies: 107
Views: 63360

Re: Send GCode Directly to OctoPrint

Also a vote for this - +1 if it can send to duet also! - Simplify3d is a premium product, so are the duet, - im surprised that they don't work that much better togheter than they currently do.
by martin1454
Sun Oct 14, 2018 2:45 am
Forum: Feature Requests
Topic: Print Speed for Skirt, Skirt under Support
Replies: 6
Views: 2646

Re: Print Speed for Skirt, Skirt under Support

+1 for speed and support -

-Also one thing - I would love an multiplier/width settings for the skirt, so I could have a skirt extruded at 150% to really prime my extruder and really tuck that plastic firmly in.
by martin1454
Thu Oct 04, 2018 2:57 am
Forum: Feature Requests
Topic: Gyroid fill pattern
Replies: 32
Views: 8879

Re: Gyroid infill

+1 from here
by martin1454
Thu Oct 04, 2018 2:06 am
Forum: Troubleshooting and Bug Reports
Topic: Blob on corners - Retraction setting?
Replies: 5
Views: 1985

Re: Blob on corners - Retraction setting?

It looks like you are having more than a retractions issue. Looking at your first picture (of you holding the green cube) your first layer is not right. There shouldn't be any gaps. You should calibrate your extruder's e-steps first to make sure the correct amount of filament is actually coming out...
by martin1454
Mon Oct 01, 2018 12:32 pm
Forum: Troubleshooting and Bug Reports
Topic: Blob on corners - Retraction setting?
Replies: 5
Views: 1985

Blob on corners - Retraction setting?

Hi there! - So I just built my first homemade machine - It runs a duet wifi, bondtech BMG and an E3D chimera setup. Im trying to calibrate it currently, but got an issue. When i try to print an cube, the corners gets small blobs. The blobs orcurs when the nozzle jumps from inner wall to outer perime...
by martin1454
Wed Aug 16, 2017 2:52 am
Forum: Troubleshooting and Bug Reports
Topic: Setting up E3D Cyclops heater (Dual extruder, single heater)
Replies: 2
Views: 1106

Setting up E3D Cyclops heater (Dual extruder, single heater)

Hello - I have been trying to find the correct way to setup an E3D cyclops - It can do dual extrusion with a single nozzle / heater - But when i configure my printer as an dual extruder printer, in the temperature tab, the extruder 1 and 2 have diffrent tempetrature designators, and it will not allo...

Go to advanced search