Search found 120 matches

Go to advanced search

by dalew8abz
Tue Feb 18, 2014 8:45 pm
Forum: Troubleshooting and Bug Reports
Topic: multi part printing problem
Replies: 4
Views: 2013

Re: multi part printing problem

Hi, Yes, I´ve read the tutorials! But, printing a file, that has two identical objects (I´m not talking abount the White and orange rings now) isn´t really multi-part printing... brgds sirlui, I print six pieces for a sliding-block puzzle. 2 of the pieces are identical. I import block1.stl, then I ...
by dalew8abz
Sat Feb 08, 2014 2:12 pm
Forum: General Discussion and Tips
Topic: Two Questions before buying Simplify3D
Replies: 6
Views: 3362

Re: Two Questions before buying Simplify3D

Frank, You could try going to the Contact Us page at www.simplify3d.com and requesting a trial license. They have been known to issue a time-limited key for a few folks to try before buying. They don't publicize this, and it may or may not be their policy any more to issue trials, but you won't know...
by dalew8abz
Fri Feb 07, 2014 4:35 pm
Forum: Troubleshooting and Bug Reports
Topic: Copying a model after slicing- new slice doesn't update
Replies: 3
Views: 1346

Re: Copying a model after slicing- new slice doesn't update

CADMan, Don't do what I did when I ran into the same situation. I had a "print job" of 6 parts in one run. I imported part #1, applied a process to it, imported part #2, put in a second process for it, etc., etc. Ended up trying to print each layer six times. I walked away for about 10 minutes after...
by dalew8abz
Thu Feb 06, 2014 7:51 pm
Forum: Troubleshooting and Bug Reports
Topic: Extruder leaves bed
Replies: 4
Views: 2148

Re: Extruder leaves bed

frank2, Some of us using early versions of Creator played around with Starting G-Code (in the FFF window, with Advanced shown, on the Scripts tab) to add a wipe function similar to the one used by MakerGear in building the sample files for the hex twist, bracelet, etc. Perhaps S3D incorporated it in...
by dalew8abz
Tue Jan 28, 2014 10:48 pm
Forum: General Discussion and Tips
Topic: thingomatic supported?
Replies: 3
Views: 1704

Re: thingomatic supported?

Joe,

For the rest of us: the answer was ????

Dale
by dalew8abz
Sat Jan 25, 2014 2:01 pm
Forum: Troubleshooting and Bug Reports
Topic: Help with new instalation
Replies: 3
Views: 1859

Re: Help with new instalation

Outbound, <channeling Maxwell Smart...> """""Missed it by THAT much!""""" Glad you found it! Long ago I gave up printing on WinXP / Win7 and went to using Linux Mint 13 / Cinnamon on my Dell notebook. No driver to install. Port just shows up as "TTYACM0" when I plug in the USB cable. O/S footprint i...
by dalew8abz
Tue Jan 21, 2014 10:12 pm
Forum: General Discussion and Tips
Topic: Flashforge with Sailfish Acceleration
Replies: 3
Views: 3417

Re: Flashforge with Sailfish Acceleration

jimc wrote:Not sure about the ff but my makergear m2 which runs marlin, all the acceleration is handled by the firmware not creator.
Ah, but it can be set by sending G-codes at any time -- just DON'T save to EEPROM with M500. I modify accel in my start G-code in my basic FFF.

Dale
by dalew8abz
Thu Jan 09, 2014 10:17 am
Forum: Troubleshooting and Bug Reports
Topic: PROBLEM SETTING BUILD
Replies: 11
Views: 4487

Re: PROBLEM SETTING BUILD

peppe64, Could you post your starting and ending G-code scripts as well? I think the preview includes those when it parses the G-code. Might be something in there that is driving that one set of segments. Better yet, save a .FACTORY file and post that so others can see the entire "print job". Dale
by dalew8abz
Fri Dec 27, 2013 7:46 pm
Forum: Troubleshooting and Bug Reports
Topic: PROBLEM SETTING BUILD
Replies: 11
Views: 4487

Re: PROBLEM SETTING BUILD

jimc, I'd presume that peppe64's entry fields are following the localization setup of the O/S as far as the decimal separator is concerned. peppe64, have you gone to the machine settings in S3D Creator (not the overrides in the FFF G-Code tab, but from the settings menu in Creator itself) and verifi...
by dalew8abz
Fri Dec 20, 2013 12:37 pm
Forum: General Discussion and Tips
Topic: 2.0.1 update osx - any version notes?
Replies: 7
Views: 1870

Re: 2.0.1 update osx - any version notes?

Thanks, Kenzu. If that "improved behavior for retraction between layers" is what I think it is, that was my pet peeve. Already downloaded -- let's see what it does with the arch on the torture test!

Thanks to Clayton et al for the fixes! Now I (we?) can't wait to see the manual. ;-)

Dale

Go to advanced search