Search found 16 matches: calibration z stepper

Searched query: calibration z stepperignored: z

Go to advanced search

by exxosuk
Tue Feb 13, 2024 8:45 am
Forum: General Discussion and Tips
Topic: Y-axis short
Replies: 6
Views: 940
 
Jump to post

Re: Y-axis short

... up the belt. I have also adjusted the stepper gear because I think it was causing the ... at 50,25 each. This could be explained by the Z axis being out now it seems. It was supposed to ... at 50,06mm. Considering Y wasn't perfect in calibration there was likely a 0.1mm error or thereabouts ...
by myprinter
Tue Jul 07, 2020 9:38 am
Forum: Troubleshooting and Bug Reports
Topic: Small Circle accurate?
Replies: 1
Views: 1444
 
Jump to post

Small Circle accurate?

... the diameter is not accurate. From about 4,5mm and up it is spot on! Calibration is spot on with a 30x15 mm cube and layer height is spot on too. ... Can it be slip or play in the moving parts on my printer, or maybe x-y stepper or what else?
by dkightley
Wed Aug 14, 2019 11:27 am
Forum: Troubleshooting and Bug Reports
Topic: Vertical size problem
Replies: 2
Views: 1504
 
Jump to post

Re: Vertical size problem

... talking X or Y dimensions.....but not for the z axis - the layer height is a function of the physical ... then you most probably have an issue with the calibration of the Z axis stepper motor. You've not said what your printer is. If ...
by ikaplinsky
Thu Jan 11, 2018 7:39 am
Forum: Troubleshooting and Bug Reports
Topic: Stuttering causing tiny blobs on parts
Replies: 5
Views: 3223
 
Jump to post

Re: Stuttering causing tiny blobs on parts

... board is good, from my point the benefit of this board that it has 6 stepper drivers onboard and you could use Diamond extruder with no additional ... Smoothie (ware) because (Marlin(RichCatell)/Repetier) has no reliable calibration algorithm implemented and I have a flat issue Now I use Smoothieware ...
by Grim
Tue Jan 02, 2018 6:06 am
Forum: General Discussion and Tips
Topic: Tronxy 5S Profile & Printquality issues
Replies: 7
Views: 7968
 
Jump to post

Re: Tronxy 5S Profile & Printquality issues

... for your answers, Currently the gap between nozzle and print-bed is .12 mm which would be pretty ... build plate, or just a small tiny space like a calibration cube or a benchy. And while this is ... my plan from flashing it, to overwrite factory stepper settings in s3d. Unfortunately this cant ...
by edanweis
Tue Jun 13, 2017 10:06 am
Forum: Troubleshooting and Bug Reports
Topic: Troubleshooting strange printing problem
Replies: 0
Views: 1232
 
Jump to post

Troubleshooting strange printing problem

... with Sigma Progen profiles - 0.6mm brass nozzle (w/thermal paste mod) - 0.1mm layer height ... changing filament - upgrading printer (latest stepper drivers) - changing extrusion width - performing full calibration All without success. You can view the gcode ...
by JWest
Fri Feb 03, 2017 5:40 am
Forum: General Discussion and Tips
Topic: Calibrating Firmware
Replies: 3
Views: 1817
 
Jump to post

Calibrating Firmware

... Pro and I have noticed after printing the calibration cube from thingiverse (http://www.thingiverse.com/thing:1278865) ... are off as follows: x = 19.85 y = 19.93 z = 19.7 So i used their formula given [ (expected ... to print the cube again but this time the stepper sounded quite different when ...
by bananaman
Tue Oct 25, 2016 7:37 pm
Forum: General Discussion and Tips
Topic: Out of ideas - print surface issue
Replies: 17
Views: 11569
 
Jump to post

Out of ideas - print surface issue

... Ramps and Marlin 1.1.0-RC7 I have done the calibrations needed, eSteps, extruder, PID, stepper current etc and then rechecked. Dimensionally, prints are very good. It has no slop, z is very good, belts and tight. Its using an original J-head ...
by tom
Sat Jan 23, 2016 3:06 pm
Forum: General Discussion and Tips
Topic: CubePro Compatibility
Replies: 76
Views: 82245
 
Jump to post

Re: CubePro Compatibility

... ENDSTOPPULLUP_YMAX // #define ENDSTOPPULLUP_ZMAX // #define ENDSTOPPULLUP_XMIN // #define ENDSTOPPULLUP_YMIN ... DISABLE_MAX_ENDSTOPS #endif // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting ... primary usage is for the Z Axis to eliminate calibration or bed height changes. ...
by simonm
Tue Nov 24, 2015 6:05 am
Forum: General Discussion and Tips
Topic: CTC Bizer Dual Extruder spare parts
Replies: 0
Views: 1375
 
Jump to post

CTC Bizer Dual Extruder spare parts

... i am going to have very soon i think is spare parts. the metal bar the stepper motors sit on has 2 very very small grubscrews that are a nightmare ... the dual heads at the right height to work together . then the nozzle calibration which is not possible with the repg print out as without priming ...

Go to advanced search