Search found 65 matches

Go to advanced search

by bapro
Wed Oct 28, 2015 3:47 pm
Forum: General Discussion and Tips
Topic: Heated bed temperature decreases during print
Replies: 10
Views: 8223

Re: Heated bed temperature decreases during print

I bet that Becky is right. And I´ve reed somewere that It´s recommended to lower the temperature to between 80 and 90 degrees after the first layer to prevent the cables and connections to break. Here is another community if your seeking answers related to Wanhao. https://groups.google.com/forum/#!f...
by bapro
Tue Oct 27, 2015 7:53 am
Forum: Troubleshooting and Bug Reports
Topic: Skirt/Brim bug ??
Replies: 4
Views: 1825

Skirt/Brim bug ??

Hi,
Skirt/Brim does not seem to be affected by the first layer underspeed.
I have difficulty to make it stick. Should it not be printed with the same underspeed?
by bapro
Tue Oct 27, 2015 7:36 am
Forum: Feature Requests
Topic: Flat surface filling
Replies: 5
Views: 2052

Re: Flat surface filling

+1
Angle options for
Top / Bottom
Bridge
and
Raft
by bapro
Sat Oct 17, 2015 1:01 pm
Forum: General Discussion and Tips
Topic: Modelling program.
Replies: 15
Views: 8562

Re: Modelling program.

How about Blender. I haven´t used it my self but i´ve seen lot great stuff done with it. And it´s free, open source.
It´s not for mechanical engineering, more like skulptrering and 3d-picture making. You can save obj-file and I think you can save stl also.
https://www.blender.org/download/
by bapro
Thu Oct 15, 2015 8:48 am
Forum: Troubleshooting and Bug Reports
Topic: Raft separation distance and next layer height problem
Replies: 58
Views: 45801

Re: Raft separation distance and next layer height problem

The raft is going the opposite direction as it did in version 2. This results in worse bottom surface, higher bounding and less accurate prints because you have to add more space between the raft and your print. Since we also lost the possibility to change solid infill angle in V3 it´s not much to d...
by bapro
Wed Oct 14, 2015 12:49 pm
Forum: Troubleshooting and Bug Reports
Topic: Problems Removing Raft
Replies: 16
Views: 14465

Re: Problems Removing Raft

It was no problem at all with 0,14 separation in V2. The raft angle goes the other way in V3 wich makes it difficult. Since they also managed to take away the possability to control the solid infill angle in V3 :( , there is nothing else but to go down to a minimum of temp for the first bottom layer...
by bapro
Thu Oct 08, 2015 8:54 am
Forum: Troubleshooting and Bug Reports
Topic: Solid infill angel bug
Replies: 4
Views: 1354

Re: Solid infill angel bug

I can´t se any reason why it shouldn´t work with the new infill patterns and I haven´t found any documentation on this change. In V2 it works just fine and there is probably a lot of more reasons to change your solid infill angles than the internal if you want a good print. Now if Simplify launched ...
by bapro
Thu Oct 08, 2015 2:55 am
Forum: Troubleshooting and Bug Reports
Topic: Solid infill angel bug
Replies: 4
Views: 1354

Re: Solid infill angel bug

That´s not true. That setting is for solid layers to. It´s a bug in V3.
by bapro
Thu Oct 08, 2015 2:42 am
Forum: Troubleshooting and Bug Reports
Topic: Nozzle diameter different than actual extruded filament
Replies: 9
Views: 3906

Re: Nozzle diameter different than actual extruded filament

That´s not how you do it. You should build a single wall. The recommendation is to set your extrusion width no lower than 1,2 times your nozzle diameter.
If you wan´t good adhesion between the layers you have to squeeze down the filament a bit.
by bapro
Wed Oct 07, 2015 1:59 am
Forum: Troubleshooting and Bug Reports
Topic: Solid infill angel bug
Replies: 4
Views: 1354

Solid infill angel bug

Solid infill angle don´t work at all. -45 or 45 degrees on solid infill no matter settings.
viewtopic.php?f=23&t=3617

Go to advanced search