Search found 1374 matches
- Fri Dec 16, 2016 7:31 am
- Forum: Troubleshooting and Bug Reports
- Topic: print stops before complete
- Replies: 5
- Views: 2139
- Jump to post
Re: print stops before complete
Along with Brian's comments. Make sure you leave the card in the reader for file transfer from the software long enough. Check file size if needed to see if it is reasonable.
- Thu Dec 15, 2016 11:18 am
- Forum: General Discussion and Tips
- Topic: Infill angle?
- Replies: 3
- Views: 2904
- Jump to post
Re: Infill angle?
Well ... The first part is 100mm by 100mm. I wanted to try scaling it to 150mm in each direction but to fit the bed better I rotated it by 45. So picture a V laying on the bed with the point going to the back of the machine. My concern was I did not want the infill to run parallel to the perimeters ...
- Thu Dec 15, 2016 8:02 am
- Forum: General Discussion and Tips
- Topic: Infill angle?
- Replies: 3
- Views: 2904
- Jump to post
Infill angle?
On a standard rectilinear infill set at 45's (default). Is this angle in relation to the bed or the part? I have a part that is a corner brace, basically two sides at a 90 degree angle to each other like an "L" bracket. If I print this with one side parallel to the side of the bed and one ...
- Tue Dec 13, 2016 3:10 pm
- Forum: Troubleshooting and Bug Reports
- Topic: Poor extrusion at layer start points.
- Replies: 8
- Views: 5181
- Jump to post
Re: Poor extrusion at layer start points.
I ran it with inside-out and the exterior is better but the problem moves to the inside walls of the part.brian442 wrote:I usually find that inside-out perimeters give better results on my machines, so make sure to test both on your printer
- Mon Dec 12, 2016 12:44 pm
- Forum: Troubleshooting and Bug Reports
- Topic: Startup Gcode Script for FlashForge Creator Pro
- Replies: 8
- Views: 9806
- Jump to post
Re: Startup Gcode Script for FlashForge Creator Pro
That's the one. I haven't tried it yet.
- Mon Dec 12, 2016 6:57 am
- Forum: Troubleshooting and Bug Reports
- Topic: Startup Gcode Script for FlashForge Creator Pro
- Replies: 8
- Views: 9806
- Jump to post
Re: Startup Gcode Script for FlashForge Creator Pro
Search the forum for new scripts. Someone, and I forget who, recently posted new ones. If I can find it I will post.
- Sat Dec 10, 2016 9:18 am
- Forum: Troubleshooting and Bug Reports
- Topic: Poor extrusion at layer start points.
- Replies: 8
- Views: 5181
- Jump to post
Re: Poor extrusion at layer start points.
Yea, I did and inside - out is much better. Odd thing is they say that the outside - in is supposed to give a better exterior. I would like to try to improve this though.
- Fri Dec 09, 2016 4:38 pm
- Forum: General Discussion and Tips
- Topic: FF Creator Pro Updated Starting script (better priming)
- Replies: 9
- Views: 9159
- Jump to post
Re: FF Creator Pro Updated Starting script (better priming)
Haven't had a chance to try it yet. I am working on getting Slic3r to work on the FFCP. Just a project. I use Slic3r on my MK2 so I wanted to try it on another printer to see how it does.
- Fri Dec 09, 2016 9:25 am
- Forum: Troubleshooting and Bug Reports
- Topic: PETG/Filament building up on nozzle during large print.
- Replies: 7
- Views: 4919
- Jump to post
Re: PETG/Filament building up on nozzle during large print.
It started as a "good job" finding an issue but digressed when I read it!
- Fri Dec 09, 2016 7:35 am
- Forum: Troubleshooting and Bug Reports
- Topic: PETG/Filament building up on nozzle during large print.
- Replies: 7
- Views: 4919
- Jump to post
Re: PETG/Filament building up on nozzle during large print.
I would research on the speed because I think that is really fast. Each to his own but just a suggestion.
Good catch on the nozzle though.
Good catch on the nozzle though.
