Search found 392 matches

Go to advanced search

by airscapes
Sat Feb 12, 2022 10:33 pm
Forum: General Discussion and Tips
Topic: duplicate a set of process that are grouped
Replies: 3
Views: 578
 
Jump to post

Re: duplicate a set of process that are grouped

airscapes wrote: Sat Feb 12, 2022 7:08 pm Hate when I answer my own posts.. but I'll be..
If you select all the processes and hit control-C and the control-V it freaking does a copy and paste! No right click menu but the key board short cuts work.. no if it will actually work life will be good!
And yep, it worked..
by airscapes
Sat Feb 12, 2022 7:08 pm
Forum: General Discussion and Tips
Topic: duplicate a set of process that are grouped
Replies: 3
Views: 578
 
Jump to post

Re: duplicate a set of process that are grouped

Hate when I answer my own posts.. but I'll be..
If you select all the processes and hit control-C and the control-V it freaking does a copy and paste! No right click menu but the key board short cuts work.. no if it will actually work life will be good!
by airscapes
Sat Feb 12, 2022 6:10 pm
Forum: General Discussion and Tips
Topic: duplicate a set of process that are grouped
Replies: 3
Views: 578
 
Jump to post

duplicate a set of process that are grouped

Still using 4.01 so this may not be possible... Have a 2 process job, bottom 2mm is standard and rest is vase mode. Can't do a single process as the bottom has a hole in the center and a single vase with 6 bottoms will bridge over the center hole. My issue is I want to lay out 6 parts to print them ...
by airscapes
Sun Dec 26, 2021 3:06 pm
Forum: Troubleshooting and Bug Reports
Topic: GeeeTech A10T and ABS
Replies: 6
Views: 6748
 
Jump to post

Re: GeeeTech A10T and ABS

I never use a raft. If the contact area is small I use a skirt of 5 or 6 perimeters .03mm from the object (additions tab) . This will help hold the object to the build plate but is easy to remove from the object when done. I am actually removing an abs print from the printer when I am done with this...
by airscapes
Sat Dec 25, 2021 2:43 pm
Forum: Troubleshooting and Bug Reports
Topic: GeeeTech A10T and ABS
Replies: 6
Views: 6748
 
Jump to post

Re: GeeeTech A10T and ABS

You need a heated enclosure to print ABS without difficulty, it needs to be 50C, the bed I normally heat to 110C and the hot end 235-240. No raft needed if your starting Z offset is set correctly.. meaning a 3mm tall model is exactly 3mm when printed. Your first layer should be 100% just like every ...
by airscapes
Thu Nov 04, 2021 6:35 pm
Forum: General Discussion and Tips
Topic: Order of Printing Multiple Parts
Replies: 11
Views: 5887
 
Jump to post

Re: Order of Printing Multiple Parts

remove the center model so you have a circle
by airscapes
Tue Oct 26, 2021 3:35 pm
Forum: General Discussion and Tips
Topic: Simplify 3D- One computer/ Two MakerGear M2's
Replies: 5
Views: 2841
 
Jump to post

Re: Simplify 3D- One computer/ Two MakerGear M2's

buy a raspberry pi and install octoprint.. stop using S3d to control your printer, it is a slicer .. you slice, up load gcode to octoprint and then print from there. Did this so long ago it is on a Pi 3 which was new at the time.. Only caveat I found is the pi wireless sucks, even on the pi 4 so I u...
by airscapes
Mon Oct 25, 2021 9:46 am
Forum: General Discussion and Tips
Topic: Initial Settings
Replies: 3
Views: 2161
 
Jump to post

Re: Initial Settings

Never had much luck with the software's profiles. I save factory files which includes all settings and the model I just open a file with similar part, nozzle size and filament and make whatever minor speed changes for the particular new model . Very little changes if the nozzle size and filament typ...
by airscapes
Thu Jul 29, 2021 4:55 pm
Forum: General Discussion and Tips
Topic: Is Simplify3D worth the cost?
Replies: 21
Views: 24008
 
Jump to post

Re: Is Simplify3D worth the cost?

I would suggest if this is your first slicer to go with Prusa slicer and learn that as it will continue to evolve unlike S3D
by airscapes
Mon Jul 26, 2021 11:51 am
Forum: Troubleshooting and Bug Reports
Topic: Gaps in Perimeters (Again)
Replies: 40
Views: 59117
 
Jump to post

Re: Gaps in Perimeters (Again)

BTW, I would think the main issue was the negative restart distance .. the nozzle and drive on the m2 works very well when retracting and restarting. Anything but zero in this field will cause under or over extrusion after the retraction.. same goes for coasting.. not needed with this hot end/drive ...

Go to advanced search