Search found 84 matches
- Fri Oct 24, 2014 5:04 pm
- Forum: Feature Requests
- Topic: Make Image to 3D work with jpg/jpeg
- Replies: 2
- Views: 2706
- Jump to post
Re: Make Image to 3D work with jpg/jpeg
i havent tried this feature since back in may sometime but i loaded a very good quality jpeg into s3d and it worked without an issue. this was obviously on one of the older versions so maybe something has happened since then. you and one or two others i have heard having the same problem with the j...
- Fri Oct 24, 2014 2:35 pm
- Forum: Feature Requests
- Topic: Make Image to 3D work with jpg/jpeg
- Replies: 2
- Views: 2706
- Jump to post
Make Image to 3D work with jpg/jpeg
Or remove jpg/jpeg formats.
Just so others wont waste time as I did.
Just so others wont waste time as I did.
- Sun Sep 07, 2014 2:52 am
- Forum: Feature Requests
- Topic: [ADDED] Finish all shells before move.
- Replies: 11
- Views: 5307
- Jump to post
Re: Feature request - Finish all shells before move.
Hi chathchath wrote:try out the islands without optimization setting. i get better prints without optimization and it's like 1% extra time
I use that setting, but it only works when there is "islands" in the print.
I would like to control it in all situations.
- Tue Sep 02, 2014 1:25 pm
- Forum: General Discussion and Tips
- Topic: How to solve weak vertical structures
- Replies: 5
- Views: 4936
- Jump to post
Re: How to solve weak vertical structures
Hello danieljb
No there is no solution in Simplify at the moment, but do a search on "honeycomb" on this forum and you will see that it is a "feature request".
No there is no solution in Simplify at the moment, but do a search on "honeycomb" on this forum and you will see that it is a "feature request".
- Sat Aug 30, 2014 9:54 am
- Forum: Feature Requests
- Topic: [ADDED] Finish all shells before move.
- Replies: 11
- Views: 5307
- Jump to post
[ADDED] Finish all shells before move.
Has anybody found a way to force Simplify to finish all shells before moving to next perimeter?
- Sat Aug 30, 2014 3:19 am
- Forum: General Discussion and Tips
- Topic: Retract or Coast at End?
- Replies: 4
- Views: 3944
- Jump to post
Re: Retract or Coast at End?
It is a bit hard to see details on your posted pictures.
But to me it look like you have over extrusion on both sides on the print.
If that is the case, then you need to adjust the acceleration settings on the printer.
You can read about it here: http://www.makerbot.com/sailfish/tuning/
But to me it look like you have over extrusion on both sides on the print.
If that is the case, then you need to adjust the acceleration settings on the printer.
You can read about it here: http://www.makerbot.com/sailfish/tuning/
- Wed Aug 27, 2014 10:26 am
- Forum: Feature Requests
- Topic: Feature Request: Custom Internal Infill Patterns
- Replies: 4
- Views: 5504
- Jump to post
Re: Feature Request: Custom Internal Infill Patterns
+1
I like this alot!
Nice way to get around any patent.
I like this alot!
Nice way to get around any patent.
- Mon Jun 23, 2014 7:36 am
- Forum: General Discussion and Tips
- Topic: Should I enable Acceleration Sailfish with Simplify3d?
- Replies: 1
- Views: 1480
- Jump to post
Re: Should I enable Acceleration Sailfish with Simplify3d?
YesMilestone85 wrote:Should I enable Acceleration Sailfish with Simplify3d?
I had it disabled from using makerware where it has its own acceleration (slow down for corners things like that)... should I have it ON for Simplify?
using a Flashforge X
- Sat Jun 21, 2014 11:29 pm
- Forum: General Discussion and Tips
- Topic: NEW version today, or yesterday...2.1.1
- Replies: 26
- Views: 11402
- Jump to post
Re: NEW version today, or yesterday...2.1.1
Thank you for clarifying that.vOidward wrote:I checked the Gcode for wipes in 2.1.0 a few days ago, it was moving past previously.
Seams always looked pretty good to me in S3D, not sure if I notice a difference.
New release did change something for me just not sure what, but it works
- Sat Jun 21, 2014 10:36 am
- Forum: General Discussion and Tips
- Topic: NEW version today, or yesterday...2.1.1
- Replies: 26
- Views: 11402
- Jump to post
Re: NEW version today, or yesterday...2.1.1
yes, but did it move backward before?TenKOhms wrote:i believe the wipe finishes the layer, then continues onward for a little bit to "wipe" away the hot end, then continues onto the next layer.
