Search found 83 matches

Go to advanced search

by inventabuild
Sat May 19, 2018 11:31 pm
Forum: Feature Requests
Topic: Add Z-Lift On Last Layer Retraction
Replies: 3
Views: 1607

Add Z-Lift On Last Layer Retraction

Please offer option of z-lift on last retraction of a layer. Optionally you can add a "start layer" tab in scripts then I could add z-lift to "layer change" tab and -(z-lift) to "start layer" tab. There is currently no way to have z-lift occur on the last retraction in a layer and then compensate fo...
by inventabuild
Mon May 14, 2018 8:37 pm
Forum: Feature Requests
Topic: Please Separate Outline Overlap & Solid Infill Overlap
Replies: 0
Views: 572

Please Separate Outline Overlap & Solid Infill Overlap

Sometimes solid infill is printing beautifully, but the Outline Overlap needs to be increased to eliminate gaps between the perimeter and the infill which, the way S3D is currently setup, also increases the solid infilll overlap. This causes excessive solid infill to be printed leading to stringing ...
by inventabuild
Thu Mar 29, 2018 9:27 pm
Forum: Feature Requests
Topic: Only Coast When Crossing Open Spaces
Replies: 0
Views: 582

Only Coast When Crossing Open Spaces

I think we should have the ability to Only Coast When Crossing Open Spaces, here's why: S3D currently has Only Retract When Crossing Open Spaces, but usually retraction is good to prevent too much ooze even when printing the solid portion of the part to keep the current layer relatively flat for the...
by inventabuild
Thu Mar 15, 2018 11:21 pm
Forum: Feature Requests
Topic: Brim Pillar, Skirt and Ooze Shield For Every Layer
Replies: 9
Views: 3268

Re: Brim Pillar, Skirt and Ooze Shield For Every Layer

Hello Aha,

I was using v4.0. I spent alot of time trying to find a solution, doing test prints and explaining the problem. It's ashame the issue hasn't been acknowledged by s3d support and fixed.
by inventabuild
Tue Jan 23, 2018 10:02 pm
Forum: General Discussion and Tips
Topic: Outline Overlap Affecting Outline Perimeter
Replies: 1
Views: 4955

Outline Overlap Affecting Outline Perimeter

If the Outline Overlap % is increased from say 25% to 90% does that effect the extrusion width of the Perimeter to which the Outline Overlap bonds to? It seems like the Perimeter is wider and not as precise / detailed when printing letters if the Outline Overlap is 90% vs when its 25%. Not sure if t...
by inventabuild
Sun Oct 29, 2017 2:51 pm
Forum: Feature Requests
Topic: Brim Pillar, Skirt and Ooze Shield For Every Layer
Replies: 9
Views: 3268

Re: Brim Pillar, Skirt and Ooze Shield For Every Layer

In addition, I suggested when both extruders are printed on the same layer, print the new extruder skirt or ooze shield right up against the side of the old extruder skirt or ooze shield so it latches on, so both extruders don't need to print on every layer if the part does not require it. Furthermo...
by inventabuild
Sun Oct 29, 2017 2:48 pm
Forum: Feature Requests
Topic: Brim Pillar, Skirt and Ooze Shield For Every Layer
Replies: 9
Views: 3268

Re: Brim Pillar, Skirt and Ooze Shield For Every Layer

Bottom line is, for dual extrusion S3D does not print any combination of skirt, prime pillar and ooze shield in the correct order so that the new extruder always gets primed properly and the old extruder always gets wiped properly before the new extruder starts printing. You can single out the Ooze ...
by inventabuild
Sat Oct 28, 2017 10:18 pm
Forum: Feature Requests
Topic: Brim Pillar, Skirt and Ooze Shield For Every Layer
Replies: 9
Views: 3268

Re: Brim Pillar, Skirt and Ooze Shield For Every Layer

I am doing a dual extrusion print now where Skirts is set to All Extruders and S3D is printing the skirts out of order as follows: Skirt Ext 1 Skirt Ext 2 Part Ext 1 What's the point of printing Ext 2 Skirt right before printing Ext 1 part? That's just going to create threads and specks of material ...
by inventabuild
Fri Oct 27, 2017 10:18 pm
Forum: Feature Requests
Topic: Brim Pillar, Skirt and Ooze Shield For Every Layer
Replies: 9
Views: 3268

Re: Brim Pillar, Skirt and Ooze Shield For Every Layer

Thanks, I don't believe I can do this with the Brim Pillar and Ooze Shield and while the Skirt can do this, the Skirt does not print in the correct order for a dual extruder setup. S3D prints both skirts at the same time one right after the other, then prints the layers one right after the other and...
by inventabuild
Thu Oct 26, 2017 9:23 pm
Forum: Feature Requests
Topic: Brim Pillar, Skirt and Ooze Shield For Every Layer
Replies: 9
Views: 3268

Brim Pillar, Skirt and Ooze Shield For Every Layer

1. Please offer the option for the Brim Pillar to print on every layer for all extruders before the layer starts printing. It is not printing for both extruder # 1 and extruder # 2 on every layer in a dual extruder setup. Perhaps the option to make a separate pillar for each extruder or half layers ...

Go to advanced search