Baroquemon
Posts: 1
Joined: Fri Jun 16, 2017 6:10 am

printer not communicating

Fri Jun 16, 2017 6:25 am

Hi everyone,

I recently got a Tevo Tarantula and i am using simplify3D. But now i am getting some very strange issues.

It started when i had to abort a print. since then my printer won't print from sd-card. It skips the heating step, start showing it reads the SD but nothing moves or gets warm.

When i connected it to a pc i could print again. But i had to stop another print. And since then i can connect over usb but still nothing happens when i want him to print. I get this:

Attempting connection at \\.\COM2...
READ: start
Connected to machine!
READ: echo:Marlin 1.1.3
Marlin 1.1.3
READ:
READ: echo: Last Updated: 2017-06-04 12:00 | Author: (Alex Perez, Tevo Tarantula)
Last Updated: 2017-06-04 12:00 | Author: (Alex Perez, Tevo Tarantula)
READ: Compiled: Jun 16 2017
READ: echo: Free Memory: 3590 PlannerBufferBytes: 1264
Free Memory: 3590 PlannerBufferBytes: 1264
READ: echo:EEPROM version mismatch (EEPROM=? Marlin=V38)
EEPROM version mismatch (EEPROM=? Marlin=V38)
READ: echo:Hardcoded Default Settings Loaded
Hardcoded Default Settings Loaded
READ: echo: G21 ; Units in mm
G21 ; Units in mm
READ: echo: M149 C ; Units in Celsius
M149 C ; Units in Celsius
READ:
READ: echo:Filament settings: Disabled
Filament settings: Disabled
READ: echo: M200 D1.75
M200 D1.75
READ: echo: M200 D0
M200 D0
READ: echo:Steps per unit:
Steps per unit:
READ: echo: M92 X80.00 Y80.00 Z1581.90 E97.09
M92 X80.00 Y80.00 Z1581.90 E97.09
READ: echo:Maximum feedrates (units/s):
Maximum feedrates (units/s):
READ: echo: M203 X225.00 Y225.00 Z3.00 E25.00
M203 X225.00 Y225.00 Z3.00 E25.00
READ: echo:Maximum Acceleration (units/s2):
Maximum Acceleration (units/s2):
READ: echo: M201 X1000 Y1000 Z100 E10000
M201 X1000 Y1000 Z100 E10000
READ: echo:Acceleration (units/s2): P<print_accel> R<retract_accel> T<travel_accel>
Acceleration (units/s2): P<print_accel> R<retract_accel> T<travel_accel>
READ: echo: M204 P1000.00 R3000.00 T3000.00
M204 P1000.00 R3000.00 T3000.00
READ: echo:Advanced: S<min_feedrate> T<min_travel_feedrate> B<min_segment_time_ms> X<max_xy_jerk> Z<max_z_jerk> E<max_e_jerk>
Advanced: S<min_feedrate> T<min_travel_feedrate> B<min_segment_time_ms> X<max_xy_jerk> Z<max_z_jerk> E<max_e_jerk>
READ: echo: M205 S0.00 T0.00 B20000 X15.00 Y15.00 Z0.40 E5.00
M205 S0.00 T0.00 B20000 X15.00 Y15.00 Z0.40 E5.00
READ: echo:Home offset:
Home offset:
READ: echo: M206 X0.00 Y0.00 Z0.00
M206 X0.00 Y0.00 Z0.00
READ: echo:Material heatup parameters:
Material heatup parameters:
READ: echo: M145 S0 H180 B60 F0
M145 S0 H180 B60 F0
READ: M145 S1 H240 B110 F0
READ: echo:PID settings:
PID settings:
READ: echo: M301 P4.53 I0.37 D123.63
M301 P4.53 I0.37 D123.63
READ: echo: M304 P322.41 I57.88 D448.99
M304 P322.41 I57.88 D448.99
SENT: T0
SENT: M105
READ: echo:SD card ok
READ: echo:SD card ok
SENT: M105
SENT: M105
SENT: M105
SENT: M105
SENT: M105
SENT: M105
SENT: M105
SENT: M105
SENT: M105
SENT: M105
SENT: M105
SENT: M105

As you can see: simplify3d is not recieving any response.
i reflashed the firmware, but nothing changed.
Does anyone know how to fix this?

Return to “Troubleshooting and Bug Reports”