Search found 33 matches

Go to advanced search

by ururk
Mon Apr 01, 2019 10:19 pm
Forum: General Discussion and Tips
Topic: Extrusion width - how does it work?
Replies: 2
Views: 281

Re: Extrusion width - how does it work?

Excellent! That's what it appeared to be doing, but wanted to check as I have a process that uses a .3mm nozzle and a .3mm perimeter width.
by ururk
Wed Mar 27, 2019 5:08 pm
Forum: General Discussion and Tips
Topic: Extrusion width - how does it work?
Replies: 2
Views: 281

Extrusion width - how does it work?

How does changing the extrusion width effect the extrusion rate? The help bubble that pops up says: The desired single-outline width of the plastic extrusion What I'm really wondering; If I have a .3mm nozzle, and set this to 0.30mm - will S3D attempt to achieve a .3mm wide line, by extruding less? ...
by ururk
Sat Dec 15, 2018 5:13 pm
Forum: Troubleshooting and Bug Reports
Topic: [FIXED] 4.1 Vase Mode Defect
Replies: 13
Views: 2263

Re: 4.1 Vase Mode Defect

Thanks for trying that out - I'll bring it into Magics on Monday and see what it can do (from what I recall, there aren't any limitations).
by ururk
Fri Dec 14, 2018 6:25 pm
Forum: Troubleshooting and Bug Reports
Topic: [FIXED] 4.1 Vase Mode Defect
Replies: 13
Views: 2263

Re: 4.1 Vase Mode Defect

Would you mind posting the repaired file? I'll run through to see if the defects remain. It seems the shared workstations (which have the program I usually use) are closed for the weekend.

Thanks!
by ururk
Fri Dec 14, 2018 6:21 pm
Forum: Troubleshooting and Bug Reports
Topic: [FIXED] 4.1 Vase Mode Defect
Replies: 13
Views: 2263

Re: 4.1 Vase Mode Defect

What program are you using? I'll see if I can clean it up in Magics.
by ururk
Fri Dec 14, 2018 6:04 pm
Forum: Troubleshooting and Bug Reports
Topic: [FIXED] 4.1 Vase Mode Defect
Replies: 13
Views: 2263

Re: 4.1 Vase Mode Defect

S3D v4.0.0 - same distortions as 4.0.1

S3D v3.1.0 - I stopped at this version, but was curious what it would do. This had some small repeating defects.
3.1.0.png
by ururk
Fri Dec 14, 2018 5:58 pm
Forum: Troubleshooting and Bug Reports
Topic: [FIXED] 4.1 Vase Mode Defect
Replies: 13
Views: 2263

Re: 4.1 Vase Mode Defect

For all of these I tried rotating the model, but the defects traveled with the surface they were on. From version to version, the defects were NOT in the same place. S3D v4.1.1 - this was supposed to address some vase printing defects, but for this print is the worst: 4.1.1.png As you can see, in a ...
by ururk
Fri Dec 14, 2018 5:48 pm
Forum: Troubleshooting and Bug Reports
Topic: [FIXED] 4.1 Vase Mode Defect
Replies: 13
Views: 2263

Re: 4.1 Vase Mode Defect

Seeing some problems with all S3D versions going back to 3.10 (and probably earlier) with a specific model. First I'm attaching the factory file and stl from Thingiverse - you can see the original model here: https://www.thingiverse.com/thing:1913982 Please note I also used an online tool to "fix" t...
by ururk
Wed Jun 20, 2018 7:50 am
Forum: General Discussion and Tips
Topic: Impossible slice?
Replies: 13
Views: 1126

Re: Impossible slice?

I decided to print it (Printrbot Model 3 kit, Mosaic Palette+):

Before:
IMG_9563.jpg
After some cleanup:
IMG_9564.jpg
by ururk
Mon Jun 18, 2018 6:14 pm
Forum: General Discussion and Tips
Topic: Impossible slice?
Replies: 13
Views: 1126

Re: Impossible slice?

It turns out you CAN print infill without perimeters:
IMG_9552.jpg

Go to advanced search