I never had one single glitch or any problems with my UM2.
No other slicers or earlier versions of S3D is giving me problems.
ONLY S3D V4.0 is giving me problems.
Search found 10 matches
- Sat Mar 03, 2018 11:58 am
- Forum: Troubleshooting and Bug Reports
- Topic: UM2 print stops after random amount of time
- Replies: 10
- Views: 7512
- Jump to post
- Thu Mar 01, 2018 3:25 pm
- Forum: Troubleshooting and Bug Reports
- Topic: [FIXED] Freeze for few seconds middle of printing
- Replies: 29
- Views: 29207
- Jump to post
Re: Freeze for few seconds middle of printing
Same problem with my UM2, printing via SD card.
There is a bug in V4
There is a bug in V4
- Thu Mar 01, 2018 3:21 pm
- Forum: Troubleshooting and Bug Reports
- Topic: UM2 print stops after random amount of time
- Replies: 10
- Views: 7512
- Jump to post
Re: UM2 print stops after random amount of time
So the “solution” it that there is a bug in the firmware of my UM2? I really doubt that.
Cura, no problems
3Dsimplify before V4.0, no problems.
I guess I am forced to downgrade 3Dsimplify or use Cure until the bug is found
Cura, no problems
3Dsimplify before V4.0, no problems.
I guess I am forced to downgrade 3Dsimplify or use Cure until the bug is found
- Wed Feb 28, 2018 10:19 am
- Forum: Troubleshooting and Bug Reports
- Topic: UM2 print stops after random amount of time
- Replies: 10
- Views: 7512
- Jump to post
Re: UM2 print stops after random amount of time
Attached factory file
- Wed Feb 28, 2018 10:18 am
- Forum: Troubleshooting and Bug Reports
- Topic: UM2 print stops after random amount of time
- Replies: 10
- Views: 7512
- Jump to post
Re: UM2 print stops after random amount of time
Hi You are more than welcome to ask for what information you need to solve the problem. I always print via SD card. I am using Windows10 Here is a youtube video showing the printer where it was stopped and resume after a while: https://www.youtube.com/watch?v=DwiiDY9ZCJ0 It did that a couple of time...
- Tue Feb 27, 2018 1:12 pm
- Forum: Troubleshooting and Bug Reports
- Topic: Ranom pauses during print
- Replies: 10
- Views: 7522
- Jump to post
Re: Ranom pauses during print
I have the exact same problem with my UM2.
It is a error in Simplify 4.0 since I did not have the problem before upgrading.
Also if I use Cura I have no problem.
It is a error in Simplify 4.0 since I did not have the problem before upgrading.
Also if I use Cura I have no problem.
- Tue Feb 27, 2018 1:11 pm
- Forum: Troubleshooting and Bug Reports
- Topic: UM2 print stops after random amount of time
- Replies: 10
- Views: 7512
- Jump to post
UM2 print stops after random amount of time
I have not been printing for a while but has since last time I upgraded Simplify3D to latest version. Now I can not use it with my UM2 anymore. Everytime I want to print, it prints a random amount of time and then stops. When it stops it is anything between a few seconds to 20-40 seconds before it s...
- Sat Dec 26, 2015 4:44 pm
- Forum: General Discussion and Tips
- Topic: Retraction on strange places??
- Replies: 4
- Views: 2104
- Jump to post
Re: Retraction on strange places??
Ok. Thanks for your answer.
I must admit that I was hoping that "what I see is what I get". Otherwise I don't know what I get.
I must admit that I was hoping that "what I see is what I get". Otherwise I don't know what I get.
- Fri Dec 25, 2015 1:52 pm
- Forum: General Discussion and Tips
- Topic: Retraction on strange places??
- Replies: 4
- Views: 2104
- Jump to post
Re: Retraction on strange places??
File is attached.
I can understand the need for retraction on the angled wall, but between layer 130 and 240 there is a lot of retraction in the middel of nowhere.
I have defined the start points to be on the back of the boots.
I can understand the need for retraction on the angled wall, but between layer 130 and 240 there is a lot of retraction in the middel of nowhere.
I have defined the start points to be on the back of the boots.
- Thu Dec 24, 2015 8:48 am
- Forum: General Discussion and Tips
- Topic: Retraction on strange places??
- Replies: 4
- Views: 2104
- Jump to post
Retraction on strange places??
Just buy and installed Simplify3D I have not made any prints with it yet on my UM2. I would like to make "clean surfaces" and using the "choose start point closed to the specific position" however Simplify3D seems to will make a retraction in the middel of a path?? (se attached)....
