Update: Fixed it by "reset all settings" and just starting over.
Must have been some random bug introduced somehow.
Search found 9 matches
- Tue Aug 04, 2015 11:43 am
- Forum: Troubleshooting and Bug Reports
- Topic: Bed Leveling Wizard not working (v3.0.1, Leapfrog Creatr)
- Replies: 3
- Views: 1685
- Jump to post
- Tue Aug 04, 2015 11:25 am
- Forum: Troubleshooting and Bug Reports
- Topic: Bed Leveling Wizard not working (v3.0.1, Leapfrog Creatr)
- Replies: 3
- Views: 1685
- Jump to post
Re: Bed Leveling Wizard not working (v3.0.1, Leapfrog Creatr
Joej - thanks for the report.
I was wondering about the the firmware. I'll look into it. Can you check the version you have installed?
Matt
I was wondering about the the firmware. I'll look into it. Can you check the version you have installed?
Matt
- Mon Aug 03, 2015 3:48 pm
- Forum: Troubleshooting and Bug Reports
- Topic: Bed Leveling Wizard not working (v3.0.1, Leapfrog Creatr)
- Replies: 3
- Views: 1685
- Jump to post
Bed Leveling Wizard not working (v3.0.1, Leapfrog Creatr)
Still not working right with Leapfrog Creatr after update to 3.01
Z moves are a violent shuddering motion, and table doesn't return to zero Z height.
Anyone have a solution?
Z moves are a violent shuddering motion, and table doesn't return to zero Z height.
Anyone have a solution?
- Thu Jul 30, 2015 11:28 am
- Forum: Troubleshooting and Bug Reports
- Topic: [SOLVED] Bed leveling wizard not working properly
- Replies: 5
- Views: 3386
- Jump to post
Re: [SOLVED] Bed leveling wizard not working properly
still not working right with Leapfrog Creatr after update to 3.01
Acts very strangely. Shuddering motion, lowers way down at each move!
Acts very strangely. Shuddering motion, lowers way down at each move!
- Sat Mar 21, 2015 6:49 pm
- Forum: Troubleshooting and Bug Reports
- Topic: Motors Moving Extreeeemly Slow (about 1step/sec)
- Replies: 7
- Views: 5066
- Jump to post
Re: Motors Moving Extreeeemly Slow (about 1step/sec)
Update: I discovered a workaround, but it doesn't explain why this suddenly started happening. If I delete the line near the start of the S3D gcode " M201 X1000 Y1000 Z500" everything seems to work. Strangely, if I delete just the next line "M202 X1000 Y1000 Z500" things seemed t...
- Sat Mar 21, 2015 1:48 pm
- Forum: Troubleshooting and Bug Reports
- Topic: Motors Moving Extreeeemly Slow (about 1step/sec)
- Replies: 7
- Views: 5066
- Jump to post
Re: Motors Moving Extreeeemly Slow (about 1step/sec)
Hi - 1 should have mentioned that I did "reset all" a couple times.
I even reinstalled S3D, reinstalled the firmware, and replaced the mega2560 chip.
I even reinstalled S3D, reinstalled the firmware, and replaced the mega2560 chip.
- Fri Mar 20, 2015 7:29 pm
- Forum: Troubleshooting and Bug Reports
- Topic: Motors Moving Extreeeemly Slow (about 1step/sec)
- Replies: 7
- Views: 5066
- Jump to post
Motors Moving Extreeeemly Slow (about 1step/sec)
I have a Leapfrog Creatr dual. The other day all motors suddenly stopped moving during a print, although there was no error message and the print completed. I discovered a fried diode on the bottom of the electronics board in the power path that feeds all the stepper motor drivers. I replaced the di...
- Tue Apr 22, 2014 10:23 am
- Forum: Troubleshooting and Bug Reports
- Topic: Major bug, x-axis leaning to the right (positive)
- Replies: 102
- Views: 126351
- Jump to post
Re: Major bug, x-axis leaning to the right (positive)
I will test if you still need people!
- Thu Apr 17, 2014 6:33 pm
- Forum: Troubleshooting and Bug Reports
- Topic: Major bug, x-axis leaning to the right (positive)
- Replies: 102
- Views: 126351
- Jump to post
Re: Major bug, x-axis leaning to the right (positive)
I am suddenly having the same issue using Leapfrog creatr and Simplify 3d. - Rotating the part 90deg does not change it (lean is still in X dir). - Re-generating STL file with different settings does not help. - Print seems OK for the 1st cm or so, then the lean starts (see pic). - I printed other p...
