Search found 94 matches

Go to advanced search

by PinballGeorgio
Wed Jul 19, 2017 6:37 am
Forum: General Discussion and Tips
Topic: infill cooling fan settings
Replies: 4
Views: 951

Re: infill cooling fan settings

Thanx! will try that.
by PinballGeorgio
Tue Jul 18, 2017 9:10 am
Forum: General Discussion and Tips
Topic: infill cooling fan settings
Replies: 4
Views: 951

infill cooling fan settings

I'm searching for an option of only activating layer cooling for the perimeter lines, so that the infill is not cooled and therefore should maintain best possible layer adhesion.

Is this possible in S3D?
by PinballGeorgio
Wed Jul 12, 2017 6:19 am
Forum: General Discussion and Tips
Topic: Elegible for upgrade?
Replies: 11
Views: 9741

Re: Elegible for upgrade?

jfkansas wrote:The price isn't that high. Most industrial software runs into the 1000's a year with maintenance contracts additional.

It will most likely by a small upgrade fee for previous users.
I'm not having an industrial printer, it's a hobby printer!
by PinballGeorgio
Wed May 10, 2017 2:25 am
Forum: Troubleshooting and Bug Reports
Topic: Wanhao D4s settings for PLA
Replies: 12
Views: 6028

Re: Wanhao D4s settings for PLA

Np. Here it is
by PinballGeorgio
Fri Apr 14, 2017 7:27 pm
Forum: Troubleshooting and Bug Reports
Topic: print quality advice
Replies: 2
Views: 555

Re: print quality advice

You need a better cooling fan/ system, but I bet you are printing this because of that :)
by PinballGeorgio
Tue Mar 14, 2017 3:16 pm
Forum: General Discussion and Tips
Topic: Top surface with PETg
Replies: 14
Views: 3265

Re: Top surface with PETg

Try printing with a lower temperature.
by PinballGeorgio
Tue Feb 28, 2017 6:22 pm
Forum: General Discussion and Tips
Topic: Surface printed on top of infill issue
Replies: 6
Views: 1103

Re: Surface printed on top of infill issue

Yet another person gets bitten by the "not extending skins far enough into the infill" bug that the S3D devs have known about for coming on for two years now. People say that the devs read these messages, I don't think there's anyone there at all. BAM, this is a real problem with S3D But be careful...
by PinballGeorgio
Sat Feb 18, 2017 9:45 pm
Forum: General Discussion and Tips
Topic: Ninjaflex or similar in a wanhao 4s, what settings?
Replies: 1
Views: 1109

Re: Ninjaflex or similar in a wanhao 4s, what settings?

Start with a PLA profile. Set the printing speed for al actions the same. 25mm/sec is a good starting point. retraction at zero. Use a skirt to get the flex flowing. 3 lines must be enough. Bed temperature 60 degrees, nozzle temp at 230. Don't use the load filament option of the wanhao 4S. This goes...
by PinballGeorgio
Fri Dec 23, 2016 8:26 pm
Forum: General Discussion and Tips
Topic: Profil for UM2+
Replies: 5
Views: 1020

Re: Profil for UM2+

Let me know if the print is better with this settings
by PinballGeorgio
Tue Dec 20, 2016 5:33 am
Forum: General Discussion and Tips
Topic: Profil for UM2+
Replies: 5
Views: 1020

Re: Profil for UM2+

At your service.

Standard profile was not good for nice prints.

Go to advanced search