Search found 20 matches

Go to advanced search

by jhaupt
Mon Jan 27, 2020 9:35 am
Forum: Troubleshooting and Bug Reports
Topic: Connection error
Replies: 17
Views: 1849

Re: Connection error

Quick update: I realized I was still running 4.0.0. I just updated to 4.1.2 and it's working for now.
by jhaupt
Thu Jan 16, 2020 12:55 pm
Forum: Troubleshooting and Bug Reports
Topic: Connection error
Replies: 17
Views: 1849

Re: Connection error

Same problem on Linux (Debian). I find that it usually starts working if I restart my computer, but sometimes it takes a few tries. No firewall in my case, and as of a few months ago this problem didn't exist. It had been fine, and then one day it just started having this connection error. I tried r...
by jhaupt
Tue Jan 02, 2018 10:55 am
Forum: Feature Requests
Topic: Allow Single Extrusion Fill for Internal Layers Only
Replies: 0
Views: 640

Allow Single Extrusion Fill for Internal Layers Only

Hello, I just discovered the "Allow Single Extrusion Fill" option under Think Wall Behavior, which has reduced build time significantly on some large prints. However, the quality of this kind of infill is such that it can look quite bad on top (external) layers. It would be very nice to be able to t...
by jhaupt
Sun Dec 31, 2017 3:39 pm
Forum: Troubleshooting and Bug Reports
Topic: [FIXED] Very Large Parts Fail to Slice
Replies: 4
Views: 763

Re: Very Large Parts Fail to Slice

What a difference a 0.0.1 version change makes. That fixed it, completely. Thank you.
by jhaupt
Sat Dec 30, 2017 9:38 pm
Forum: Troubleshooting and Bug Reports
Topic: [FIXED] Very Large Parts Fail to Slice
Replies: 4
Views: 763

Re: Very Large Parts Fail to Slice

Oh interesting. I'm on 4.0.0. I'll try upgrading tomorrow and try again.
by jhaupt
Sat Dec 30, 2017 6:41 pm
Forum: Troubleshooting and Bug Reports
Topic: [FIXED] Very Large Parts Fail to Slice
Replies: 4
Views: 763

[FIXED] Very Large Parts Fail to Slice

I haven't previously had cause to print large parts (~500mm on a side), but now that I do I'm finding Simplify3D is having trouble consistently. After clicking "Prepare to Print" it gets to where it says "Calculating Infill..." and then just hangs. The same behavior happens on several similarly size...
by jhaupt
Sat Dec 30, 2017 4:42 pm
Forum: General Discussion and Tips
Topic: Multiple Heated Bed Temperature Controllers
Replies: 1
Views: 468

Re: Multiple Heated Bed Temperature Controllers

P.S.

A better workaround than what I described is to remove the default heated bed controller from the settings altogether and turn all the zones on in the start script. Still not fantastic but at least then the whole bed comes on at once.
by jhaupt
Sat Dec 30, 2017 12:16 pm
Forum: General Discussion and Tips
Topic: Multiple Heated Bed Temperature Controllers
Replies: 1
Views: 468

Multiple Heated Bed Temperature Controllers

Hello, I have a 5-zone heated bed (four quadrants plus perimeter heat) running with a Duet+Duex5, which supports multiple bed heater outputs as of the latest firmware release. I found a reference to someone saying Simplify3D supports multiple bed heaters (https://forum.simplify3d.com/viewtopic.php?f...
by jhaupt
Tue Dec 26, 2017 6:28 pm
Forum: Feature Requests
Topic: Please make profile change prompt optional
Replies: 1
Views: 463

Re: Please make profile change prompt optional

+1 I suggested this well over a year ago but, I think, didn't word the suggestion as clearly as you. Of all the things I could think to change with this [wonderful] software, this is my #1. Because of this issue I'm very careful to export my FFF profile when I make a change. Occasionally I'll wipe o...
by jhaupt
Fri May 13, 2016 10:30 am
Forum: Feature Requests
Topic: A notes section
Replies: 23
Views: 6632

Re: A notes section

I know this is an old topic but +1. A notes panel in the FFF settings window would be extremely useful.

Go to advanced search